Premium Paint for your Toys! TM
About
Welcome to the world wide headquarters for Monster Kolor. This interactive community is a place for all who are interested in the custom painting of toys of all kinds. Feel free to look around, but I encourage you to join in.
Events
Featured Member
Application Guide
Monster Kolor Application Instructions
1. Wipe figure down 2-3 times with 70% rubbing alcohol THROUGHLY ! (even in the hard to reach areas)
2 Pour color directly into airbrush..For brighter color application shake up & spray white base as your first coat and then layer your colors on top of the white.
3. Layer your colors in sequence from light to dark. Example : White,Yellow,Orange,Blue, Purple,etc
Color can be poured back into bottle to eliminate waste
4. After Colors are applied now you can add specialty paints direct over paints. Example : Pearls,Flakes,etc
Note : the colors will appear dull in appearence up to this point. Dont worry this is correct.
5. Once all paint is applied, warm over figure with blow dryer to dry up any remaining areas in preperation for clear coating.
6. Clear Coat : Use in a well ventilated area! Must use an OSHA approved respirator while spraying. This is a 2 component system. It is mixed 2:1 ( 2 parts clear 1 part activator) . Mix small amount with mixing cup provided. For micro mixture please mix 1 part clear ½ part activator.
Usually, 1 coat of clear is all that’s required for the desired gloss level. If you chose to do 2 coats please allow 15 minutes wait time before 2nd coat of clear application.
7. Place figure in a dust free environment at 60 degrees or warmer for 24 hours to cure.
8. If your going to store Monster Kolor for a long period of time between uses I recommend placing the cap plugs back into the bottles to avoid air getting into the bottle and possibly evaporating the solvents out of the paint.
1. Wipe figure down 2-3 times with 70% rubbing alcohol THROUGHLY ! (even in the hard to reach areas)
2 Pour color directly into airbrush..For brighter color application shake up & spray white base as your first coat and then layer your colors on top of the white.
3. Layer your colors in sequence from light to dark. Example : White,Yellow,Orange,Blue, Purple,etc
Color can be poured back into bottle to eliminate waste
4. After Colors are applied now you can add specialty paints direct over paints. Example : Pearls,Flakes,etc
Note : the colors will appear dull in appearence up to this point. Dont worry this is correct.
5. Once all paint is applied, warm over figure with blow dryer to dry up any remaining areas in preperation for clear coating.
6. Clear Coat : Use in a well ventilated area! Must use an OSHA approved respirator while spraying. This is a 2 component system. It is mixed 2:1 ( 2 parts clear 1 part activator) . Mix small amount with mixing cup provided. For micro mixture please mix 1 part clear ½ part activator.
Usually, 1 coat of clear is all that’s required for the desired gloss level. If you chose to do 2 coats please allow 15 minutes wait time before 2nd coat of clear application.
7. Place figure in a dust free environment at 60 degrees or warmer for 24 hours to cure.
8. If your going to store Monster Kolor for a long period of time between uses I recommend placing the cap plugs back into the bottles to avoid air getting into the bottle and possibly evaporating the solvents out of the paint.
Replies to This Discussion
-
Permalink Reply by Javier Jimenez on -
Thanks for the super fast response Matt.
That would be cool and highly appreciated! If you haven't send the second package yet (for S&D) maybe you can just include it there.
Thanks again!
-
Permalink Reply by Dead Presidents on -
I will include it in those box!
Javier Jimenez said:Thanks for the super fast response Matt.
That would be cool and highly appreciated! If you haven't send the second package yet (for S&D) maybe you can just include it there.
Thanks again!
- ‹ Previous
- 1
- …
- 14
- 15
- 16
- Next ›
© 2013 Created by Dead Presidents.
